Single Medium Dog Kennel w/ Drawers Plans & Instructions

Designed to comfortably house one medium sized dog (30- 50lbs), or multiple smaller puppies. Top is wide enough to hold a large TV and decors. This is a nice showpiece for the living room, and can be stained or painted to match rest of the furniture.

Get the complete Medium Dog Kennel DIY Plans – Instant PDF download 8.5″ x 11″
PDF includes the cut list, additional diagrams and dimensions, complete step-by-step DIY instructions.

Buy Complete PDF Plan

Material and Cut List

(A) 2 – 2×4 Lumber: 36 3/4″
(B) 2 – 2×4 Lumber: 18 1/2″
(B) 1 – 2×2 Lumber: 18 1/2″
(C) 2 – 1×3 Lumber: 33 1/4″
(D) 2 – 1×3 Lumber: 33 3/4″
(E) 1 – 1×3 Lumber: 38 1/4″
(F) 2 – 1×10 Lumber: 25 1/2″
(G) 4 – 1×3 Lumber: 24 1/2″
(H) 1 – 1×3 Lumber: 25 1/2″
(I) 1 – 3/4″ Plywood: 36 3/4″ x 25 1/2″
(J) 6 – 1×6 Lumber: 38 1/4″
(J) 1 – 1×4 Lumber: 38 1/4″
(K) 2 1×3 Lumber: 36 3/4″
(L) 3 1×3 Lumber: 20 1/2″
(M) 2 1×3 Lumber: 18″
(N) 2 1×2 Lumber: 19 1/2″
(O) 4 1×8 Lumber: 40 1/4″
(P) Drawer Materials: Refer to Step 7

11 – 3/8″ Diameter Rebar: 26 1/2″
3 – 3/8″ Diameter Rebar: 21 1/2″
Rust-Oleum Epoxy Metal Paint

HARDWARE
– (2) 3″ T-Hinge Hardware
– (2) 3″ Barrel Bolts
– 1 1/4″ Pocket Screws
– 2 1/2″ Pocket Screws
– 3/8″ Dowels

PROJECT TOOLS
– Tape Measure
– Pocket-hole Jig
– Cordless Drill
– Miter Saw / Circular Saw
– Screwdriver
– Sandpaper or Sand Block
– Refer to the woodworking tool guide for more information

Step 1 – Kennel Base

Cut the 2×4 lumbers per cut list dimensions. The bottom frame is made from two 36 3/4″ 2×4’s and two 18 1/2” 2×4’s, with 2×2 for center bracing. Arrange the 2×4’s per layout below. You can use wood glue to assemble each lumber first. Then, drill pocket-holes and use 2 1/2” size screws to secure in place.

All vertical panels will sit directly on top of the bottom frame, with 1” offset from the perimeter edges. Finish building all the panels first before screwing them into the bottom frame, to ensure all the panels fit in place properly. Drill pocket-holes in the 1×3 panels and use 1 1/4” screws to secure to the bottom 2×4 frame.

Step 2 – Front and Side Panels

Next, cut the 1×2 and 1×3 lumbers per cut list for the front facing panel. You will need two 33 3/4” 1×3’s, one 38 1/4” 1×3’s, one 24 1/2″ 1×3, two 33 1/2″ 1×2’s, and three 26 1/2” rebar. Drill dual pocket-holes on both ends of the 1×3’s. Only screw into the bottom lumber piece first. Then, drill 3/8” diameter holes (1” depth) into both the top and bottom lumber to fit the rebar.

Before installing the metal rebars in place, you will need to prepare and paint them to avoid rusting. The best type of pet-friendly paint for metal is the Rust-Oleum Specialty Epoxy Spray Paint, which is ideal for refinishing metal surfaces and provide a durable finish. Don’t worry, this process is simple! First, clean the metal rebars of any dirt or rust, then spray two coats of the epoxy paint directly onto the rebars. Allow 2-4 hours to complete dry before installing them on the kennel doors.

Insert the 3/8” rebars into the holes. Finally, add the top lumber piece and secure it in place with 1 1/4” pocket screws.

Next, cut 1×2 and 1×3 lumbers per cut list for the side panels. You will need two 33 3/4” 1×3’s, one 38 1/4” 1×3’s, one 24 1/2″ 1×3, two 33 1/2″ 1×2’s,  and three 26 1/2” rebars. Total of two side panels. Drill dual pocket-holes on both ends of the 1×3’s. Only screw into the bottom lumber first until you insert the rebar in place.

Step 2 – Flooring

The floor panel is made out of 3/4” plywood, cut to dimensions below. You can use 2” nails to secure the floor panel onto the bottom frame.

Step 4 – Top Bracing

The top support frame will add more structural integrity to the kennel. Cut 1×3’s per dimension below, drill pocked holes and secure with 1 1/4” nails. Position the frame in place, with top aligning with the drawer opening. See next page for section. You can also use 1 1/2” angle brackets to attach the support frame.

Step 5 – Back Panel

The back panel is made up of six 38 1/4” 1×6’s and a single 38 1/4” x 3 1/4” lumber. Drill pocket-holes per location indicated below, then glue and secure in place with 1 1/4” screws. You can also use other lumber sizes or 3/4” plywood sheet to build this 38 1/4” x 36 1/4” back panel.

Step 6 – Kennel Doors

Next, cut 1×3 lumbers per cut list for the door panels. You will need two 18” 1×3’s, two 19 1/2” 1×3’s, and three 19 1/2” rebars, per door. Similar to the previous panels, drill dual pocket-holes on both ends of the 19 1/2” 1×3’s. Only screw into the bottom lumber first.

3″ T-Hinge Hardware: https://amzn.to/3KjrpsJ
3″ Barrel Bolts: https://amzn.to/3TcPpBR

Step 7 – Kennel Drawers

Almost there! We will use 1×6’s, 1×8’s, and 1/4” plywood to build out the drawer. Leave 1/2” gap between the drawer box for drawer slides. Cut the drawer panels and use 1 1/4” pocket screws to secure together, attached 1/4” plywood to the bottom with nails.

Finally, cut four 40 1/4” 1×8’s for the table top piece. Drill pocket-holes as indicated in the layout below, then use 1 1/4” screws to secure in place. Pocket-hole side will face the bottom side. You can also construct the table top using other lumber sizes or plywood, as long as the overall dimensions are the same.

Need another kennel size? Check out my shop for more kennel design and sizes. The full PDF plans include the full materials list, cut list, complete dimensions, 2D/3D diagrams, step-by-step instructions, and helpful tips. Thank you for your support!

The post Medium Dog Kennel With Drawers DIY Plans appeared first on Build Blueprint.

Tall Double Dog Kennel TV Stand DIY Plans

Designed to comfortably house two large sized dogs (30” headroom), while keeping them separated. Each bay fits a standard large dog bed. This is the perfect showpiece for the living room, and can be stained or painted to match rest of the furniture. You can choose to add 2 or 4 drawers to this design. This build requires basic woodworking tools including pocket-hole jig, miter saw, screw driver, and wood glue.

Get the complete Tall Double Kennel TV Stand plan – Instant PDF download 8.5″ x 11″

PDF includes the cut list, additional diagrams and dimensions, complete step-by-step DIY instructions.

Buy Complete PDF Plan

Material and Cut List

(1) 2×4 – 10′-0″
(2) 2×4 – 8′-0″
(7) 1×3 – 10′-0″
(7) 1×6 – 10′-0″
(1) 1×6 – 8′-0″
(4) 1×8 – 8′-0″
(2) 1×2 – 10′-0″
(2) 1×2 – 8′-0″
(4) 3/4″ Plywood – 41 1/8″ x 25 1/2″
(28) 3/8″ Diameter Rebar – 30″
(6) 3/8″ Diameter Rebar – 25″
Rust-Oleum Epoxy Metal Paint

HARDWARE
– (4) 3″ T-Hinge Hardware
– (4) 3″ Barrel Bolts
– (4) 5″ Bar Drawer Handles
– 1 1/4″ Pocket Screws
– 2 1/2″ Pocket Screws
– 3/8″ Dowels

PROJECT TOOLS
– Tape Measure
– Pocket-hole Jig
– Cordless Drill
– Miter Saw / Circular Saw
– Screwdriver
– Sandpaper or Sand Block
– Refer to the woodworking tool guide for more information

Step 1

First, cut the 2×4 lumbers per cut list dimensions. The bottom frame is made from two 86 1/2” 2×4’s and five 22” 2×4’s. Arrange the 2×4’s per layout below. You can use wood glue to assemble each lumber first. Then, drill pocket-holes and use 2 1/2” size screws to secure in place.

Step 2

Next, cut 1×3 lumbers per cut list for the front facing panel. You will need two 84 1/2” 1×3’s, five 28” 1×3’s, and ten 30” rebar. Drill dual pocket-holes on both ends of the 28” 1×3’s. Only screw into the bottom lumber first. Then, drill 3/8” diameter holes (1” depth) into both the top and bottom lumber to fit the rebar.

Before installing the metal rebars in place, you will need to prepare and paint them to avoid rusting. The best type of pet-friendly paint for metal is the Rust-Oleum Specialty Epoxy Spray Paint, which is ideal for refinishing metal surfaces and provide a durable finish. Don’t worry, this process is simple! You can first clean the metal rebars of any dirt or rust, then spray two coats of the epoxy paint directly onto the rebars. Allow 2-4 hours to complete dry before installing them on the kennel doors.

Build the side and center divider panels with the same process. Then, secure the vertical face panels to the base using 3/8″ dual pocket screws.

Step 3

Floor panels and top shelf panels will be identical, so you can make 2 set of this. Cut the 3/4” plywood per dimensions below. Place directly on top of the bottom frame, use 2 1/2” screws to secure into the bottom frame.

Step 4

Next, cut the 1×3 lumbers per cut list for the door panels. You will need two 18” 1×3’s, two 23” 1×3’s, and three 25” rebar, per door. Two sets of doors total. Similar to the previous panels, drill dual pocket-holes on both ends of the 1×3’s. Only screw into the bottom lumber first. Rebar spacing is 3 1/4” O.C. adjust per your dog’s size. Complete cut and dimensions available in the PDF plan version. 

Step 5

The back panel is made up of seven 84 1/2” 1×6’s. Drill pocket-holes per location indicated, then glue and secure in place with 1 1/4” screws. You can also use other lumber sizes or 3/4” plywood to build this 84 1/2” x 38 1/2” back panel.

Step 6

Measure the cut ten 1×6’s to 25 1/2” and five 1×3’s to 4”. Refer to the dimensions below for the exact placements. This will create four identical 18” drawer bays. Drill 3/8” pocked holes and secure with wood screws. Fill with 3/8” dowel where visible.

Step 7

Next, we will use 1×6’s, 3/4” and 1/4” plywood to build out the drawer. Leave 1/2” gap between the drawer box for drawer slides. Cut the drawer panels and use 1 1/4” pocket screws to secure together, attached 1/4” plywood to the bottom with nails.

Complete drawer build instructions available in the PDF plan version.

Step 8

Next, cut four 1×8’s (you can use 2×8’s if you want a thicker table top) to 86 1/2” length for the table top. Drill pocket-holes as indicated in the layout below, then use 1 1/4” screws to secure in place. Pocket-hole side will face the bottom side. You can also construct the table top using other lumber sizes or plywood, as long as the overall dimensions are the same.

Step 9

Before staining or painting your completed kennel, sand down the wood surface until it is a fine texture. The best type of stain for furniture is oil-based stains. Oil-based stains will penetrate deeper and give it a finer finish, but takes longer time to dry. To paint your kennel, use either a satin or semi-gloss finish in either a latex or an oil based paint. Prime the surface first and let dry, then apply coats of the paint of your choice.

Attach the doors with 3″ T-Hinge Hardware on top and bottom hinge location. Then, install 3″ Barrel Bolts to complete the doors. I found both of these hardware that fits the dimensions on Amazon, links below for reference:

3″ T-Hinge Hardware: https://amzn.to/3KjrpsJ
3″ Barrel Bolts: https://amzn.to/3TcPpBR

Finally, add 5″ black metal bar drawer handles, on center with each drawer face.

5″ Bar Drawer Handles (5 pack): https://amzn.to/3A53OHd

Need another kennel size? Check out my shop for more kennel design and sizes. The full PDF plans include the full materials list, cut list, complete dimensions, 2D/3D diagrams, step-by-step instructions, and helpful tips. Thank you for your support!

The post Tall Double Dog Kennel TV Stand DIY Plans appeared first on Build Blueprint.

Kennel Bottom Structure DIY Plan:

The bottom portion of this dog kennel tv stand is exactly the same as the Medium Double Dog Kennel build, please build the bottom panels using these plans first before continuing.

Get the complete Double Kennel TV Stand plan – Instant PDF download 8.5″ x 11″

PDF includes the cut list, additional diagrams and dimensions, complete step-by-step DIY instructions.

Buy Complete PDF Plan

Next, purchase and cut the following materials in order to build the kennel shelves, drawers, and table top.

(A) 2 – 3/4″ Plywood: 20 1/2″ x 33 7/8″
(B) 4 – 1×3 Lumber: 5 1/2″
(C) 8 – 1×6 Lumber: 20 1/2″
(D) 3 – 2×6 Lumber: 70 1/2″
(D) 1 – 2×8 Lumber: 70 1/2″
(E) 2 – 1×2 Lumber: 72″
(E) 2 – 1×2 Lumber: 24″
(F) Drawer Materials:
1 – 1×6 Lumber: 20″
2 – 3/4″ Plywood: 20″ x 4″
1 – 3/4″ Plywood: 17 1/2″ x 4″
1 – 1/4″ Plywood: 19″ x 20″

Support Materials:
4 – 1×2 Lumber: 30 7/8″
4 – 1×2 Lumber: 20 1/2″

HARDWARE
– Rust-Oleum Epoxy Metal Paint
– (4) 3″ T-Hinge Hardware
– (4) 3″ Barrel Bolts
– (3) 5″ Bar Drawer Handles
– 1 1/4″ Pocket Screws
– 2 1/2″ Pocket Screws
– 3/8″ Dowels

PROJECT TOOLS
– Tape Measure
– Pocket-hole Jig
– Cordless Drill
– Miter Saw / Circular Saw
– Sandpaper or Sand Block
– Refer to the woodworking tool guide for more information

Step 1

First, we will build out the kennel’s top shelves, this is where the drawers will insert to (you can also leave them as cubbies). Cut the 1×6 lumbers and 3/4″ plywood per cut list dimensions below, you will need 2 identical plywood for the shelf panels.

Step 2

Before placing the shelf panels in place, we will need to build out the supports using 1×2’s. Cut four 1×2’s to 30 7/8″ and four more 1×2’s to 20 1/2″, you can use wood glue and 1 1/4″ pocket screws to secure these in place. These will sit directly below the two shelf panels, so about 0.725″ below the top of the vertical panels, measure carefully before installing. You’ll want the top of the shelf panels to be flush with top of all the vertical panels.

Step 3

Next, install the cubby panels per layout below. The smaller front 1×3 stiles are spaced with 20″ of gap in-between each one, refer to the elevation diagram below for exact placement. Use wood glue and 1 1/4″ pocket screws to secure these in place.

Then, add in the eight cubby dividers (20 1/2″ 1×6’s) to align with the cubby stiles per layout below. Use wood glue and 1 1/4″ pocket screws to secure them in place, to create three identical cubbies. The drawers in the next step will slide into these cubbies.

Step 4

The table top panel is 24″ x 70 1/2″, you can make these out of four 2×6’s, secured together with 2 1/2″ pocket screws. The border trim is made from 1×2’s, this is optional if you want a more polished perimeter edge. Sand down the surfaces and edges before attaching the table top to the panels below.

Use 1 1/4″ pocket screws to secure the back panel, cubby stiles to the table top.

Step 5

The drawers are made out of 1×6’s and 3/4″ and 1/4″ plywood. You will also need 20″ drawer slides (available on Amazon) that attaches to the side of the drawers and cubbies. The drawers are optional for this kennel design, you can also just omit these and keep the cubbies.

Finally, add 5″ black metal bar drawer handles, on center with each drawer face. You can build up to three drawers for this kennel.

5″ Bar Drawer Handles (5 pack): https://amzn.to/3A53OHd

Insert the completed drawers into the cubbies. And just like that, your double kennel tv stand is complete!

Need another kennel size? Check out my shop for more kennel design and sizes. The full PDF plans include the full materials list, cut list, complete dimensions, 2D/3D diagrams, step-by-step instructions, and helpful tips. Thank you for your support!

The post Double Dog Kennel TV Stand DIY Plans appeared first on Build Blueprint.

Building your own dog kennel is easy and can help save you hundreds of dollars compared to buying from a custom builder. All you need are basic woodwork tools (listed below), and lumbers plus rebar from your local hardware store. Before you start, determine the best kennel size best fit for your dogs and your living space. The medium double dog kennel measures 6’L x 2’W x 27 1/2″H, with interior headroom of 24″. This is the DIY plans for medium dog kennel designed to house two medium sized dogs (30-50lbs), if you have larger dogs, check out the Large Double Dog Kennel Plans.

Get the complete Medium Dog Kennel plan – Instant PDF download 8.5″ x 11″

PDF includes the cut list, additional diagrams and dimensions, complete step-by-step DIY instructions.

Buy Complete PDF Plan

Free DIY plans for a Medium Double Dog Kennel:

Material and Cut List

(A) 2 – 2×4 Lumber: 6′-0″
(B) 3 – 2×4 Lumber: 17″
(C) 2 – 1×3 Lumber: 5′-10″
(D) 11 – 1×3 Lumber: 19 1/2″
(E) 6 – 1×3 Lumber: 20 1/2″
(F) 3 – 1×6 Lumber: 5′-10″
(F) 1 – 1×10 Lumber (ripped down to 10″): 5′-10″
(G) 4 – 1×3 Lumber: 16 1/4″
(H) 4 – 1×3 Lumber: 14 1/2″
(I) 6 – 1×6 Lumber: 33 7/8″
(I) 2 – 1×6 Lumber (ripped down to 4″): 33 7/8″
(J) 2 – 2×10 Lumber: 6′-0″
(J) 1 – 2×6 Lumber: 6′-0″

15 – 3/8″ Diameter Rebar: 21 1/2″
6 – 3/8″ Diameter Rebar: 16 1/2″
Rust-Oleum Epoxy Metal Paint

HARDWARE
– (4) 3″ T-Hinge Hardware
– (4) 3″ Barrel Bolts
– 1 1/4″ Pocket Screws
– 2 1/2″ Pocket Screws
– 3/8″ Dowels

PROJECT TOOLS
– Tape Measure
– Pocket-hole Jig
– Cordless Drill
– Miter Saw / Circular Saw
– Sandpaper or Sand Block
– Refer to the woodworking tool guide for more information

Step 1

Cut the 2×4 lumbers per cut list dimensions. The bottom frame is made from two 6’-0” 2×4’s and three 17” 2×4’s. Arrange the 2×4’s per layout below. You can use wood glue to assemble each lumber first. Then, drill pocket-holes and use 2 1/2” size screws to secure in place.

All vertical panels will sit directly on top of the bottom frame, with 1” offset from the perimeter edges. Finish building all the panels first before screwing them into the bottom frame, to ensure all the panels fit in place properly. Drill pocket-holes in the 1×3 panels and use 1 1/4” screws to secure to the bottom 2×4 frame.

Step 2

Next, cut 1×3 lumbers per cut list for the front facing panel. You will need two 5’-10” 1×3’s, five 19 1/2” 1×3’s, and six 21 1/2” rebars. Drill dual pocket-holes on both ends of the 19 1/2” 1×3’s. Only screw into the bottom 5’-10” lumber first. Then, drill 3/8” diameter holes (1” depth) into both the top and bottom lumber to fit the rebar.

Before installing the metal rebars in place, you will need to prepare and paint them to avoid rusting. The best type of pet-friendly paint for metal is the Rust-Oleum Specialty Epoxy Spray Paint, which is ideal for refinishing metal surfaces and provide a durable finish. Don’t worry, this process is simple! First, clean the metal rebars of any dirt or rust, then spray two coats of the epoxy paint directly onto the rebars. Allow 2-4 hours to complete dry before installing them on the kennel doors.

Insert the 3/8” rebars into the holes. Finally, add the top lumber and secure it in place with 1 1/4” pocket screws.

Step 3

Next, cut 1×3 lumbers per cut list for the side panels. You will need two 20 1/2” 1×3’s, two 19 1/2” 1×3’s, and three 21 1/2” rebars, per panel. Total of three side panels. Drill dual pocket-holes on both ends of the 19 1/2” 1×3’s. Only screw into the bottom lumber first.

Step 4

The dog kennel’s floor will be made from two identical panels. Cut the 1×6’s to size per cut list, you’ll need to rip down two 1×6’s to 4″. Drill pocket-holes and secure each lumber in place with 1 1/4” screws. Insert both floor panels on top of the bottom frame.

The back panel is made up of three 5’-10” 1×6’s and a single 5′-10” x 8” piece. Drill pocket holes per location indicated below, then glue and secure in place with 1 1/4” screws. You can also use other lumber sizes to build this 5′-10” x 24 1/2” back panel.

Step 5

Next, cut 1×3 lumbers per cut list for the door panels. You will need two 16 1/4” 1×3’s, two 14 1/2” 1×3’s, and three 16 1/2” rebars, per door. Two sets of doors total. Similar to the previous panels, drill dual pocket-holes on both ends of the 14 1/2” 1×3’s. Only screw into the bottom lumber first, and insert rebar per diagram below.

Attach the doors with 3″ T-Hinge Hardware on top and bottom hinge location. Then, install 3″ Barrel Bolts to complete the doors. I found both of these hardware that fits the dimensions on Amazon, links below for reference:

3″ T-Hinge Hardware: https://amzn.to/3KjrpsJ
3″ Barrel Bolts: https://amzn.to/3TcPpBR

Step 6

Finally, cut two 2×10’s, and a 2×6 to 6’-0”, for the kennel’s table top piece. Drill pocket-holes as indicated in the layout below, then use 2 1/2” screws to secure in place. Pocket-hole side will face the bottom side. You can also construct the table top using other lumber sizes, as long as the overall dimensions are the same.

Now the kennel is complete, sand and clean off the surface dusts to prepare for staining or painting.

Need another kennel size? Check out my shop for more kennel design and sizes. The full PDF plans include the full materials list, cut list, complete dimensions, 2D/3D diagrams, step-by-step instructions, and helpful tips. Thank you for your support!

The post How to Build a Double Dog Kennel: Free DIY Plan appeared first on Build Blueprint.

Large Single Dog Kennel Plans & Instructions

Designed to comfortably house one large sized dog (50lbs+), with tall interior headroom. Top is wide enough to hold a large TV and decors. This is the perfect showpiece for your living room, and can be stained or painted to match rest of the furniture! Learn to make this single dog kennel step by step, you will need basic woodworking tools. The cost of construction materials for this project is about $175, including all wood materials and hardware.

Get the complete Single Dog Kennel plans – Instant PDF download 8.5″ x 11″
PDF includes the cut list, additional diagrams and dimensions, complete step-by-step DIY instructions.

Buy Complete PDF Plan

Material and Cut List

(A) 2 – 2×4 Lumber: 45 1/4″
(B) 2 – 2×4 Lumber: 22″
(C) 2 – 1×3 Lumber: 43 1/4″
(D) 7 – 1×3 Lumber: 24 1/2″
(E) 4 – 1×3 Lumber: 25 1/2″
(F) 5 – 1×6 Lumber: 43 1/4″
(F) 1 – 1×3 Lumber (ripped down to 2″): 43 1/4″
(G) 2 – 1×3 Lumber: 18″
(H) 2 – 1×3 Lumber: 19 1/2″
(I) 4 – 1×6 Lumber: 41 3/4″
(I) 1 – 1×4 Lumber: 41 3/4″
(J) 4 – 2×8 Lumber: 45 1/4″

12 – 3/8″ Diameter Rebar: 26 1/2″
3 – 3/8″ Diameter Rebar: 21 1/2″
Rust-Oleum Epoxy Metal Paint

HARDWARE
– (2) 3″ T-Hinge Hardware
– (2) 3″ Barrel Bolts
– 1 1/4″ Pocket Screws
– 2 1/2″ Pocket Screws
– 3/8″ Dowels

PROJECT TOOLS
– Tape Measure
– Pocket-hole Jig
– Cordless Drill
– Miter Saw / Circular Saw
– Screwdriver
– Sandpaper or Sand Block
– Refer to the woodworking tool guide for more information

Step 1

Cut the 2×4 lumbers per cut list dimensions. The bottom frame is made from two 45 1/4″ 2×4’s and two 22” 2×4’s. Arrange the 2×4’s per layout below. You can use wood glue to assemble each lumber first. Then, drill pocket-holes and use 2 1/2” size screws to secure in place.

All vertical panels will sit directly on top of the bottom frame, with 1” offset from the perimeter edges. Finish building all the panels first before screwing them into the bottom frame, to ensure all the panels fit in place properly. Drill pocket-holes in the 1×3 panels and use 1 1/4” screws to secure to the bottom 2×4 frame.

Step 2

Next, cut 1×3 lumbers per cut list for the front facing panel. You will need two 43 1/4” 1×3’s, three 24 1/2” 1×3’s, and four 26 1/2” rebar. Drill dual pocket-holes on both ends of the 24 1/2” 1×3’s. Only screw into the bottom lumber piece first. Then, drill 3/8” diameter holes (1” depth) into both the top and bottom lumber to fit the rebar.

Before installing the metal rebars in place, you will need to prepare and paint them to avoid rusting. The best type of pet-friendly paint for metal is the Rust-Oleum Specialty Epoxy Spray Paint, which is ideal for refinishing metal surfaces and provide a durable finish. Don’t worry, this process is simple! First, clean the metal rebars of any dirt or rust, then spray two coats of the epoxy paint directly onto the rebars. Allow 2-4 hours to complete dry before installing them on the kennel doors.

Insert the 3/8” rebars into the holes. Finally, add the top lumber piece and secure it in place with 1 1/4” pocket screws.

Next, cut 1×3 lumbers per cut list for the side panels. You will need two 25 1/2” 1×3’s, two 24 1/2” 1×3’s, and four 26 1/2” rebars, per panel. Total of two side panels. Drill dual pocket-holes on both ends of the 24 1/2” 1×3’s. Only screw into the bottom lumber first until you insert the rebar in place.

The back panel measures 43 1/4″ x 29 1/2″, you can use any 1x lumber materials to construct this, or use 3/4″ plywood. Drill pocket holes per location indicated below, then glue and secure in place with 1 1/4” screws.

Step 3

Similarly, the floor panels will be constructed the same way. Use 3/4″ plywood or any 1x lumber material to construct the 41 3/4″ x 25 1/2″ floor panel. Drill pocket-holes and secure each lumber in place with 1 1/4” screws. Insert both floor panels on top of the bottom frame.

Step 4

Next, cut 1×3 lumbers per cut list for the door panels. You will need two 18” 1×3’s, two 19 1/2” 1×3’s, and three 19 1/2” rebars for the single door. Similar to the previous panels, drill dual pocket-holes on both ends of the 19 1/2” 1×3’s. Only screw into the bottom lumber first until you insert the rebar in place.

Attach the doors with 3″ T-Hinge Hardware on top and bottom hinge location. Then, install 3″ Barrel Bolts to complete the doors. I found both of these hardware that fits the dimensions on Amazon, links below for reference:

3″ T-Hinge Hardware: https://amzn.to/3KjrpsJ
3″ Barrel Bolts: https://amzn.to/3TcPpBR

Step 5

Finally, cut four 45 1/4” 2×8’s for the table top piece. Drill pocket-holes as indicated in the layout below, then use 2 1/2” screws to secure in place. Pocket-hole side will face the bottom side.

Good job! Your large single dog kennel is complete! The next step is to sand and clean off the surface dusts and prepare for staining or painting.

Need another kennel size? Check out my shop for more kennel design and sizes. The full PDF plans include the full materials list, cut list, complete dimensions, 2D/3D diagrams, step-by-step instructions, and helpful tips. Thank you for your support!

The post Single Dog Kennel DIY Plans appeared first on Build Blueprint.

Large Double Dog Kennel Plans & Instructions

Designed to comfortably house two large sized dogs (50lb+), while keeping them separated. Top is wide enough to hold a large TV and decors. This is a great showpiece for the living room, and can be stained or painted to match rest of the furniture. The cost of construction materials for this project is about $225, including hardware.

Get the complete Double Dog Kennel plan – Instant PDF download 8.5″ x 11″

PDF includes the cut list, additional diagrams and dimensions, complete step-by-step DIY instructions.

Buy Complete PDF Plan

Material and Cut List

(A) 2 – 2×4 Lumber: 7′-2″
(B) 3 – 2×4 Lumber: 22″
(C) 2 – 1×3 Lumber: 7′-0″
(D) 11 – 1×3 Lumber: 24 1/2″
(E) 6 – 1×3 Lumber: 25 1/2″
(F) 5 – 1×6 Lumber: 7′-0″
(F) 1 – 1×3 Lumber (ripped down to 2″): 7′-0″
(G) 4 – 1×3 Lumber: 18″
(H) 4 – 1×3 Lumber: 19 1/2″
(I) 8 – 1×6 Lumber: 40 7/8″
(I) 2 – 1×4 Lumber: 40 7/8″
(J) 4 – 2×8 Lumber: 7′-2″

20 – 3/8″ Diameter Rebar: 26 1/2″
6 – 3/8″ Diameter Rebar: 21 1/2″
Rust-Oleum Epoxy Metal Paint

HARDWARE
– (4) 3″ T-Hinge Hardware
– (4) 3″ Barrel Bolts
– 1 1/4″ Pocket Screws
– 2 1/2″ Pocket Screws
– 3/8″ Dowels

PROJECT TOOLS
– Tape Measure
– Pocket-hole Jig
– Cordless Drill
– Miter Saw / Circular Saw
– Screwdriver
– Sandpaper or Sand Block
– Refer to the woodworking tool guide for more information

Step 1

Cut the 2×4 lumbers per cut list dimensions. The bottom frame is made from two 7’-2” 2×4’s and three 22” 2×4’s. Arrange the 2×4’s per layout below. You can use wood glue to assemble each lumber first. Then, drill pocket-holes and use 2 1/2” size screws to secure in place.

All vertical panels will sit directly on top of the bottom frame, with 1” offset from the perimeter edges. Finish building all the panels first before screwing them into the bottom frame, to ensure all the panels fit in place properly. Drill pocket-holes in the 1×3 panels and use 1 1/4” screws to secure to the bottom 2×4 frame.

Step 2

Next, cut 1×3 lumbers per cut list for the front facing panel. You will need two 7’-0” 1×3’s, five 24 1/2” 1×3’s, and eight 26 1/2” rebars. Drill dual pocket-holes on both ends of the 24 1/2” 1×3’s. Only screw into the bottom 7’-0” lumber first. Then, drill 3/8” diameter holes (1” depth) into both the top and bottom lumber to fit the rebar.

Before installing the metal rebars in place, you will need to prepare and paint them to avoid rusting. The best type of pet-friendly paint for metal is the Rust-Oleum Specialty Epoxy Spray Paint, which is ideal for refinishing metal surfaces and provide a durable finish. The process is simple, you can first clean the metal rebars of any dirt or rust, then spray two coats of the epoxy paint directly onto the rebars. Allow 2-4 hours to complete dry before installing them on the kennel doors.

Insert the 3/8” rebars into the holes. Finally, add the top 7’-0” lumber and secure it in place with 1 1/4” pocket screws.

Next, cut 1×3 lumbers per cut list for the side panels. You will need two 25 1/2” 1×3’s, two 24 1/2” 1×3’s, and four 26 1/2” rebars, per panel. Total of three side panels. Drill dual pocket-holes on both ends of the 24 1/2” 1×3’s. Only screw into the bottom lumber first.

The back panel is made up of five 7’-0” 1×6’s and a single 84” x 2” piece. Drill pocket holes per location indicated below, then glue and secure in place with 1 1/4” screws. You can also use other lumber sizes to build this 84” x 29 1/2” back panel.

Step 3

Similarly, the floor panels will be constructed the same way. Cut eight 40 7/8” 1×6’s and two 40 7/8” 1×4’s. Drill pocket-holes and secure each lumber in place with 1 1/4” screws. Insert both floor panels on top of the bottom frame.

Step 4

Next, cut 1×3 lumbers per cut list for the door panels. You will need two 18” 1×3’s, two 19 1/2” 1×3’s, and three 19 1/2” rebars, per door. Two sets of doors total. Similar to the previous panels, drill dual pocket-holes on both ends of the 19 1/2” 1×3’s. Only screw into the bottom lumber first.

Step 5

Next, attach the doors with 3″ T-Hinge Hardware on top and bottom hinge location. Then, install 3″ Barrel Bolts to complete the doors. I found both of these hardware that fits the dimensions on Amazon, links below for reference:

3″ T-Hinge Hardware: https://amzn.to/3KjrpsJ
3″ Barrel Bolts: https://amzn.to/3TcPpBR

Step 6

Finally, cut four 7’-2” 2×8’s for the table top piece. Drill pocket-holes as indicated in the layout below, then use 2 1/2” screws to secure in place. Pocket-hole side will face the bottom side.

Now the kennel is complete, sand and clean off the surface dusts to prepare for staining or painting.

Need another kennel size? Check out my shop for more kennel design and sizes. The full PDF plans include the full materials list, cut list, complete dimensions, 2D/3D diagrams, step-by-step instructions, and helpful tips. Thank you for your support!

The post Double Dog Kennel DIY Plans appeared first on Build Blueprint.